Cisco 2950 switch default ip address
- Cisco 2950 switch default ip address how to#
- Cisco 2950 switch default ip address serial#
- Cisco 2950 switch default ip address full#
- Cisco 2950 switch default ip address password#
Accept the default to the SNMP Network Management prompt by pressing Enter.Enter vlan1 for the interface used to connect to the management network, andĢ. Be sure to write down the passwordsand store them in a secure place.4. If these werenot issued by your network administrator, you may choose your own passwords.Press Enter after entering each password.
Cisco 2950 switch default ip address password#
Enter the enable secret password, the enablepassword and the virtual terminal password at the respective prompts. Enter a host name of your choosing at the host name prompt, or press Enter toaccept the default of Switch. Press Enter to accept thedefaults for the prompts that ask if you would like to enter the initial configurationdialog and if you would like to enter basic management setup.3. If you have properly configured theterminal session, you will see the Cisco boot messages. Configure the session for 9600 baud, 8 data bits, 1 stop bit, noparity and no flow control. HyperTerminal, Putty or any other terminal emulator will workfine for this step. Power on the computer, and set up a terminal session using your computersterminal software. The console port end isan RJ-45 jack, which resembles a telephone jack connector, but is a little bit larger.2.
Cisco 2950 switch default ip address serial#
The cable that comes with the switch istypically blue, and the serial end is a 9-pin d-shell connector. Connect the serial cable that came with the switch to the console port on theswitch and to a serial port on your computer.
Cisco 2950 switch default ip address how to#
Before you start, be sure to get the network address and password information you will need from your network administrator.Guide: How to Configure a Catalyst 2950 Cisco Switch1.
In addition to the standard console and aux ports, the Cisco 2950 comes with 12, 24 or 48 Ethernet ports, depending on the model. The Cisco Catalyst 2950 switch is a great example of Ciscos dedication to quality and efficiency. HOW TO CONFIGURE A CATALYST 2950 CISCO SWITCH? Cisco has long been a player in the networking industry, and routers and switchesform the core of its product offerings. Vtp domain cisco1 vtp password cisco vtp pruning vtp version 1 exit vlan 10 name estudiantesĬONFIGURACION SUBINTERFACES Router Cisco 1800 R(config)# interface fastethernet 0/0 R(config-if)# no ip address R(config-if)# no shutdown R(config-if)#exit R(config)# interface fastethernet 0/0.1 #subif R(config-subif)# encapsulation dot1q 101 (101 numero de vlan) R(config-subif)# ip address 172.16.101.1 255.255.255.0 R(config)# interface fastethernet 0/0.2 #subif R(config-subif)# encapsulation dot1q 102 (102 numero de vlan) R(config-subif)# ip address 172.16.102.1 255.255.255. SW1(config)# SW1(config)# SW1(config)# SW1(config)# SW1(config)# SW1(config)# SW1(config)# SW1(config)# vtp password cisco SW1(config)# vtp mode client SW1(config)# vtp version 1 SW1(config)# exit SW1# show vtp status SERVER SW1#delete flash:vlan.dat CONFIGURACION ENLACE TRONCAL ENTRE SWITCHES SW1(config)# interface fastethernet 0/24 (Puerto troncal) SW1(config)# switchport mode trunk (cisco 2950) SW1(config)# switchport trunk encapsulation dot1q (cisco 2900) SW1(config)# switchport trunk native vlan 10 (paquetes sin etiqueta) CONFIGURACION VTP CLIENTE SW1# vlan database (cisco 2900) SW1(config)# vtp domain cisco1
Cisco 2950 switch default ip address full#
Interface fasethernet 0/18 switchport mode access switchport access vlan 99 show interface vlan 99 (ver vlan 99)ĬOLOCAR GATEWAY SW1(config)# ip SW1(config-if)# SW1(config-if)#Ī SWITCH default-gateway 172.17.99.1 speed 100 duplex full Service password-encryption no ip domain-lookup (desactivar DNS) erase startup-config (borrar conf) reload (reinicar)ĬONFIGURACION VLAN Y IP ADDRESS (CISCO 2950) SW1(config)# vlan 99 SW1(config)# name admin (CISCO 2900) SW1(config)# vlan database SW1(config)# vlan 99 name admin
Configuración Switch Cisco Catalyst 2950 y 2900 #configure terminal (configuracion de switch ) switch(config)# hostname SW1 (nombre de switch) SW1(config)# banner motd #Solo personal autorizado#ĬONTRASEÑA PARA INGRESAR COMO ADMINISTRADOR SW1(config)# enable secret class SW1(config)# line console 0 SW1(config-line)# logging synchronous SW1(config-line)# password cisco (password para ingresar x consola) SW1(config-line)# login CONFIGURACION ACCESO TELNET Y SSH SW1(config)# line vty 0 15 (hasta 16 consolas telnet de acceso) SW1(config)# password cisco1 SW1(config)# login ENCRIPTAR CONTRASEÑAS SW1(config)# SW1(config)# SW1(config)# SW1(config)#